12、我用的是金钻9代80G(7200R)的硬盘,以前用很正常,现在启动windows2000自检时,屏幕提示:Primaster hard disk:S.M.A.R.T. Status BAD.Backupand replace pressto resume. 不知道是不是硬盘有问题呀!
答:maxtor官方solution:
Backup your data if possible then download and run the PowerMax diagnostic test. PowerMax will test the S.M.A.R.T. parameters along with 30 separate tests allowing a complete hard disk health check.If PowerMax generates a six digit error code that means the drive will need to be replaced.
最好先备份重要数据,然后用
powermax(http://www.lander.com.cn/download_software_show.asp?id=5)前三项检测一下。特别是advanced test有错的话,您的硬盘只能在销售商那里送修换盘了。
检查硬盘本身的问题,可以用powermax软件(http://www.lander.com.cn/download_software_show.asp?id=5),用作成的检测软盘启动机器,首先确定显示出了正确的硬盘型号,之后用前三项检测。特别是advanced test报错的话,您的硬盘肯定是个人无法修复的。只要不执行倒数第二项——低格,就不会破坏数据。
26、关于AIDA32软件和降温的帖子:
答:(论坛网友:caoweijack)我经常用AIDA32这个软件来查看金九80的温度,后来发现SMART里面有很多数据和使用时间是有直接关系的,大家不妨讨论讨论,第一就是:start/stop Count 这个数值代表的是硬盘的通电断电次数,经过我观察,重启它是不计数的。只有硬盘断电它才计一次数字。第二是:power-on time count 字面理解就是加电工作时间,也就是硬盘的累积工作时间,单位是分钟,大家可以看看是不是这样。
另外就是可以在硬盘底下用绳子吊一个机箱风扇。对着硬盘吹,别的坛子上学的方法,昨天试了一下,效果非常好,整个硬盘下面都是强风,不开空调可以减到30度以下。
27、原C盘装的win2000系统,最近发现运行时,没有什么操作却经常硬盘灯狂闪。于是用以前备份的gho文件恢复C盘。完成后重启至 Verifying DMI Pool Data 时即死机,用软盘可以启动,DOS模式下可以正常访问该硬盘,星钻三代 Maxtor 4D040H2。
答:
A:由于没有亲自操作过,可能翻译有误,请谅解!
maxtor官方:Suggestions to Resolve the Condition:
1)Apply power to the computer. 开机(不插硬盘)。
2)Access the system BIOS. Set the drive type as None or Not Installed. Load BIOS Defaults .Load SETUP Defaults .在BIOS里,把硬盘设为NONE。
3)Save the BIOS changes and reboot the PC to a System Boot Diskette. 用启动盘重启机。
4)Shut down the PC after the memory count is displayed. 检测完内存后关机。
5)Reconnect the power and interface cables to the hard drive. 重新插上硬盘电源和数据线。
6)Access the System BIOS. 进入BIOS。
7)Auto-Detect the hard drive. Ensure that the LBA Mode option is enabled. 设为自动检测硬盘。确认LBA模式无误。
8)Save the BIOS changes and boot the PC with a System Diskette. 软盘启动。
9)Partition and format the hard drive via the operating system. 分区格式化。
10)Reboot the system. On bootup, the screen should read: 重启机,显示如下:
Verifying DMI Pool Data Update Successful
11)The system should continue booting normally. 正常。
Other Possible Solutions:
1)Apply power to the computer. 开机。
2)Access the System BIOS. 进入BIOS。
3)Disable both the Internal and External CPU Cache. These features are located in either the "BIOS Features" or "Advanced Settings" options of the BIOS Setup. NOTE: Consult the System or Motherboard User's Manual for exact location of the Internal and External CPU Cache settings. 参考系统或主板说明,在"BIOS Features"或 "Advanced Settings"选项里,将内/外部CPU Cache设置为不可用。
4)Save the BIOS changes and reboot the PC to a System Boot Diskette. On bootup, the screen should read: 重启机,显示如下:
Verifying DMI Pool Data Update Successful
The system should continue booting normally. 可以正常引导。
7)After the system successfully boots, re-start the PC and access the system BIOS.
Enable the External CPU Cache. This feature is located in the "BIOS Features" or "Advanced Settings".
NOTE: Consult the System or Motherboard User's Manual for exact location of the External CPU Cache setting.成功引导后,重启机,在BIOS里将CPU的两个项恢复为enable。
! WARNING ! User's MUST re-enable this feature for optimal system performance. 该步骤必须执行。
8)Save the BIOS changes and reboot the PC to a System Boot Diskette. On bootup, the screen should read:
Verifying DMI Pool Data
Update Successful
The system should continue booting normally.
再重启,可正常使用。
NOTE: If the aforementioned suggestions fail to resolve the issue, contact the system or motherboard manufacturer to:
Remove the "Clear CMOS" Jumper and reset the system BIOS
Obtain a Flash BIOS Upgrade
注意:如果还不行,只能试一下清CMOS、重新设置BIOS或刷新BIOS。
②木星系列 Jupiter Ganymede 80G
型号:J620/J630/J640/J660/J680 20G/30G/40G/60G/80G
界面接口 :UITRA DMA 100 OR SATA 多段缓存:2048 (千位)
旋转速度:7200转/分
10月份硬盘技术问题
一:怎样用FDISK对硬盘进行分区?
答:
1、用启动软盘引导至提示符“A:>_”,键入“Fdisk”命令,回车。英文信息最下一行“Do you wish to enable large disksupport (y/n)?”(是否希望使用大硬盘模式?),请键入“Y”,否则就无法创建超过2GB容量的硬盘分区。
2、接下来看到的是Fdisk主界面:
①Create DOS partition or logical DOS drive(创建DOS分区和逻辑驱动器)
②Set active partition(设置活动分区)
③Delete partition or logical DOS drive(删除分区或逻辑驱动器 )
④Display partition information(显示分区信息)
3、创建主DOS分区:
选择“1”,然后再选择“1. Create Primary DOS partition”(创建主DOS分区),回车。FDISK程序会询问“Do you wish to use Maximum available size for a PriMary DOS Partition and Make the Partition active(Y/N)”,缺省选择是“Y”,这样就会将全部硬盘空间都创建为一个分区,由于现在的硬盘容量一般都在40GB以上,因此建议选择“N”以创建多个分区。然后在中括号中分配主DOS分区(通常情况下即C盘)的空间,回车。创建完毕后,请按Esc键返回FDISK主菜单窗口 。
4、创建扩展DOS分区:
选择“2. Create Extended DOS Partition”,程序会提示可建立扩展DOS分区的最大空间,直接回车即可。创建结束后,程序会提醒当前还不存在逻辑盘,按Esc键可以自动进入逻辑盘创建界面,缺省是将当前全部空间创建为一个逻辑盘(即D盘)。也可手工设置多个逻辑盘。
5、设置活动分区:
按Esc键回到界面,选择“2. Set Active Partition”设置活动分区,键入“1”(即C分区)以激活主分区,否则启动时会提示错误。
6、退出Fdisk程序,重新启动系统。改变分区设置后,需重新启动才生效。